AGA ADC3PROS Guide d'installation

1AGA DUAL CONTROLModel No’s: DC3G02/16 EINS 516911For use in USA/CanadaInstallationGuidePLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING SITE SURVEYOR

10CONNECTION TO THE POWER SUPPLY - AGA DC3GElectric Shock HazardRating Plate is located behind removable plinth, see Fig. 4A, Page 11Electrical Ground

11MAINS CABLE ROUTING - AGA DC3GFig. 4DESN 516643MAINS CABLE FED FROMCONTROL TRAY LEFT OR RIGHT EXIT THROUGH DUCTING DEPENDENT UPON POSITION OF SUPPLY

12FLUE SYSTEMSEE FIGS. 5, 6, 7, 8 & 9The flue system must be installed in accordance with the federal, state and local codes. Only genuine AGA app

13DESN 511052Fig. 7DESN 511053AROUND THE HOUSEUNDER THE CAR PORT, ETC.Minimum siting dimensions for flue terminalsPosition SpacingMinimuminch/mm A Di

14Fig. 8DESN 516850

15DOWNWARD RUNS UP TO 11 3/4”(300mm) BELOW THE APPLIANCE ARE ALLOWED, PROVIDED ONLY ONE BEND IS USED.DOWNWARD RUNS USING 2 BENDS ARE NOT ALLOWED.MAXIM

16WIRING DIAGRAM - AGA DC3G Fig. 10

17GAS SUPPLY - U.S. PIPE THREADSNOTE: A MANUAL SHUT-OFF VALVE MUST BE INSTALLED IN AN ACCESSIBLE LOCATION IN THE GAS PIPE EXTERNAL TO THE APPLIANCE FO

181. Fit the handrail bracket over the fixing stud located on the top plate. Lock into position by tightening the grub screw nearest the appliance. (

193. Once the handrail assembly is located squarely, lock the handrail in position by winding in the grub screws on the underside of each handrail

2SECTION PAGEPRODUCT SAFETY 3GENERAL NOTES 4DELIVERY REQUIREMENTS 4GENERAL INSTALLATION REQUIREMENTS 4APPLIANCE DIMENSIONS - AGA DC3G 5TECHNICAL

20Fig. 14 DESN 516966Inlet Pressure Testing1. Turn off control knob (A) and turn off electrical supply to range.2. Remove facia by pulling off hotpl

21CAUTION: BEFORE LIGHTING: ENSURE KNOB (A) IS IN THE OFF POSITION (SEE FIG. 27). ALSO ENSURE GAS SUPPLY TO RANGE IS ON, AND THE GAS SERVICE COCK (C)

227. Check the condition of the flame supervision thermocouple tip to ensure it is clean and free of carbon. Heavy heat oxidised tips should mean t

23Fig. 15Fig. 17Fig. 19Fig. 16Fig. 18Fig. 20OFF POSITIONIGNITION POSITIONFLAME SUPERVISION BURNER POSITIONMAIN BURNERON POSITIONLOW FIRENORMAL RUNNING

24CONTENT LIST (LOOSE ITEMS)DESCRIPTION PART NO QTY TICKBAKING OVEN CALIBRATION PLATE AE2M231432 1 ( )OVEN GRID SHELF AE4M211863 3

25

26

27

28For further advice or information contact your local AGA AmbassadorWith AGA Marvel’s policy of continuous product improvement, the Company reserves

3PRODUCT SAFETYMEANING/DESCRIPTION SIGNIFICATION/DESCRIPTIONSYMBOLWARNING/CAUTIONAn appropriate safety instruction should be followed or caution to a

4GENERAL NOTESNOTE: THESE INSTALLATION INSTRUCTIONS SHOULD BE LEFT WITH THE RANGE AND THE USER TO RETAIN FOR FUTURE REFERENCE.DELIVERY REQUIREMENTSThe

5APPLIANCE DIMENSIONS - AGA DC3GFig. 1 DESN 516847 ARange DimensionsWhen surveying for a range installation the actual clearance required for the ‘bo

6Side ClearancesA 1/8” (3mm) gap is required each side between the range top plate and adjoining work surfaces that may be fitted, this is to allow fo

7TilingWhen the range is to stand in a recess or against a wall which is to be tiled, under no circumstances should the tiles overlap the range top pl

8NOTE: ANY OVERHEAD FITTED CABINETS MUST NOT EXCEED 13” PROJECTED DEPTH ABOVE THE RANGE.DIM ‘D’ TO BE NOT LESS THAN THE NORMAL WIDTH OF THE RANGE.Fig.

9Top Plate Adjustment - AGA DC3 (See Fig. 4)In general, adjustment of the top plate is to be avoided. However minimum use of the top plate adjusters c